The paper presents the results of research on the development of the composition of the raw mixture for the production of facing composite material for construction purposes. The composition of the raw material mixture included a brick fight as a filler, waste products from non-plasticized polyvinyl chloride as a binder and methylene chloride for dissolving polymer waste. This composition allows mixing and pressing without heating, which eliminates the possibility of destruction of the polymer component. After pressing, heat treatment is carried out at the solvent evaporation temperature. The paper shows the dependences of the main physical and mechanical characteristics of the resulting material on the degree of filling. The maximum amount of filler has been set, which allows to obtain the material without a lack of binder. With a lack of binder, a decrease in strength and an excess of the proportion of open pores over closed ones were observed. According to the results of the experiments, the polymer : solvent ratio and the degree of filling were selected, allowing to obtain a material with the maximum value of strength characteristics. Practical application of the developed composition of the raw mixture will allow complex utilization of low-demand and large-tonnage polymer and brick waste to obtain composite material for cladding buildings and structures.

Keywords: polymer composite material, facing material, polymer waste, brick fight, polyvinyl chloride, methylene chloride

The paper presents the results of studies of the characteristics of a polymer coating for the protection of steel and concrete surfaces based on low molecular weight dimethylsiloxane rubber SKTN-A. For cold curing of the binder and its modification, the MSN-7-80 hardener was used, an additional functional additive was galvanic sludge calcined at 1000 °C and crushed to a particle size of no more than 40 microns. It was found that polymethylsilazane, which is part of MSN-7-80, increases the strength characteristics of the coating, especially its cohesive strength, while reducing water absorption by increasing the hydrophobicity of the surface. In turn, galvanic sludge increases the mechanical strength upon impact. The ecological safety of the obtained material was confirmed by the method of biotesting on the mortality of Daphnia magna Straus. As a result of comparison with a protective coating similar in composition and purpose, it was revealed that the coating obtained in this work surpasses it in strength and adhesion characteristics. The developed polymer composition can be used to protect steel and concrete surfaces in construction and mechanical engineering from shock and moisture, including in extreme conditions of high or low temperatures and in contact with aggressive media.

Keywords: polymer composition, protective coating, organosilicon binder, electroplating sludge, polymethylsilazane, cold curing

The paper presents the results of a study of the effect of cerium oxide on the sintering process and the basic physico-chemical properties of ceramics based on low-plastic clay with the addition of boric acid. The developed ceramics were obtained by semi-dry pressing at a maximum firing temperature of 1050 ° C. The combined introduction of cerium oxide with boric acid promotes liquid-phase sintering, self-glazing of the ceramic surface and effective filling of pores and voids in it with the vitreous phase. At the same time, cerium oxide increases the refractoriness and chemical resistance of the vitreous phase and equalizes the coefficients of thermal expansion between the crystalline and amorphous phases in the composition of ceramics. The amount of cerium oxide has been determined, which makes it possible to optimally increase the heat resistance, chemical resistance and strength of ceramics. The practical application of the developed composition of the charge makes it possible to use raw materials of low plasticity in the production of high-quality ceramics for lining apparatuses and equipment, lining of industrial buildings and structures, etc. products experiencing mechanical stress with repeated and abrupt temperature changes, as well as in contact with aggressive media.

Keywords: ceramics, heat resistance, chemical resistance, self-glazing, low-plastic clay, cerium oxide, boric acid

The paper presents the results of a study conducted for chemically and thermally resistant ceramics obtained from low-plastic clay using boric acid as a melt, zirconium oxide and galvanic sludge as functional additives. The studied ceramics were obtained by semi-dry pressing technology at a maximum firing temperature of 1050 оC. The dependences of the physical and mechanical properties of ceramics on the content of zirconium oxide and galvanic sludge in the charge are established. Zirconium oxide promotes liquid-phase sintering, compaction and strength enhancement, and galvanic sludge exhibits a pore-forming effect due to calcium carbonate and heavy metal hydroxides in its composition. At the same time, the effect of galvanic sludge on the physical and mechanical properties is lower than that of zirconium oxide. The quantities of the studied additives have been established, which make it possible to obtain high values of operational properties and apply the resulting ceramics in the production of lining and other ceramic products for special purposes.

Keywords: heat-resistant ceramics, acid-resistant ceramics, self-glazing, low-plastic clay, galvanic sludge, zirconium oxide, boric acid