"This review covers various methods of synthesis LaMnO3 ferroics. The general analysis of the solid-phase synthesis reactions methods and wet methods (sol-gel, sorption, co-precipitation) are carred out. The original results of LaMnO3 syntheses from various precursors by means of the in situ method are showned. The advantages and disadvantages of different methods of synthesis are determined. The analysis of synthesis LaMnO3 ferroics published data is shown:
- the structure formation of LaMnO3 in perovskite-type phases occurs at different temperatures, depending on precursors states;
- LaMnO3 perovskite phases differ in symmetry and unit cells parameters at room temperature, depending on the preparation conditions;
- the highest synthesis temperature of LaMnO3 are typical for solid phase reactions method (950-1050 ° C), the lowest - for wet synthesis methods (500-700 ° C);
 - the synthesis conditions effect the stoichiometry of LaMnO3 for oxygen content.
Our studies of structure formation processes of LaMnO3 by in situ method are allowed to define the role of precursors states at synthesis of solid phase reactions methods, adsorption, co-precipitation and sol-gel mixtures.
It is determined that in samples prepared by wet chemical methods, the formation processes of  LaMnO3 perovskite phases occur at lower temperatures than by solid phase reaction (sol-gel precursor - 500 <T <600 ° C; precursors obtained by coprecipitation and sorption methods - at 600 <T <700 ° C and 700 <T <800 ° C, respectively).  

Keywords: ferroics, LaMnO3, X-ray diffraction, solid-phase synthesis, sol-gel synthesis, sorption, co-precipitation

An approach to the calculation of the optimal values ​​of the protective layer of longitudinally reinforced concrete columns, operating at a central compression. Modeling performed using FEM - Ansys package for the design and implementation of spatial models of flat section of the column.

Keywords: reinforced concrete column, longitudinal reinforcement, a protective layer of concrete, finite element method, critical load

On the basis of experimental data on the resistance of reinforced concrete columns eccentric compression was obtained analytical dependence of the limiting compressibility of concrete from the varied factors: the relative eccentricity of the external force eo / h and the reinforcement ratio μ.

Keywords: reinforced concrete column, longitudinal reinforcement, a protective layer of concrete, finite element method, critical load

The existing methods of calculation of the annual change in soil temperature. Identified areas of their application and the possible deviations from reality. The requirements to the boundary conditions of the calculation. Defines the principles of the choice of initial conditions. The preconditions for the development of a universal method of calculation.

Keywords: heat pump, renewable energy, solar radiation, transient mode, soil

The paper examines the main approaches to the modeling of scientific and technical progress. Details the conditions and change the model postulates technological structure , its main provisions . Put tasks that are of great interest for scientists involved in the modeling of scientific and technological progress , and for economists who are interested in the practical application of these results . Values ​​of other well-known models of STP . The variants of modernization and the possible synthesis of these approaches to modeling change tehnologichekogo order.

Keywords: scientific and technological progress, advanced technology, changing technological way of practical experience, the elasticity of factor capital

The especially the functioning of fluid catalytic cracking plant are considered. A mathematical model of a catalytic cracking plant is presented here. Implemented model identification based on experimental data. The predictive controller based on predictive control method for dynamic processes is developed. Effectiveness of the approach is confirmed by the results of catalytic cracking plant simulation. 

Keywords: catalytic cracking, modeling, model predictive control, multivariate control system, optimization

Zoning of territories is one of the mechanisms of real estate management. Economic analysis of real estate includes consideration of the problems of spatial – economic development of real estate which exists in specially organized space. Difference in land value, expressed through economic parameters of real estate, forms the basis of territorial – economic zoning, definition of cost equivalent of real estate objects. Global practice shows, that it is increase of land value as a result of zonal-territorial policy realization that leads to the maximal economic benefit. Only joint influence on real estate objects and their spatial environment сan provide the best social and economic results.

Keywords: Zoning of territories, real estate management, economic analysis, zonal-territorial policy realization, spatial – economic development of real estate

Problems of formation of the logistical approach to management of personnel streams of the enterprise are considered.

Keywords: Logistic, person, stream, transport, logistics sistem

In the implementation of dynamic re-routing of traffic it is important to notice that the threshold depends on the network layout and type of the roads. Full paper includes appropriate relationships, figures and analysis of simulation results to define the re-routing rate of dynamic traffic reroutig

Keywords: re-routing, rate, dynamic traffic assignment, traffic conditions

To the East Donbass agglomeration has developed thematic maps of subsiding soils, indicating their capacity, groundwater levels, surface subsidence above mining, landslide and erosion hazards. Sources of information were the materials of the geological surveys, maps and literature data, and numerical modeling. For the purposes of industrial and civil construction built the final map of the cumulative effects of geological hazards.

Keywords: geological hazard, modeling, geofiltration,subsidence, landslides, erosion, underflooding, agglomeration.

Personnel motivation strategy is a part of a strategy of the whole company. It is long-term plan of particular actions, which has an aim to develop personnel’s potential to the full extent. As an impact, this allows the company to have a competitive advantage in strategy.
There are a few main approaches to strategy development and, as a consequence, a few options of personnel motivation strategy.
When it comes to development of personnel motivation strategy, there are several stages that shall be competed, as follows: diagnostics of current personnel motivation strategy; development of main strategies, aims and principles of company’s motivation policy, as well as its content and structure;  development of employees’ material monetary and noncash remuneration, and non-financial reward; development of internal white papers in order to establish personnel motivation strategy; implementation and effect monitoring of established personnel motivation strategy.

Keywords: personnel motivation, motivation strategy, material remuneration, non-financial remuneration, effectiveness of personnel motivation.

Consider the use of management system of heating and ventilation plants in greenhouses, uniform distribution of heat and humidity in the area of biological objects, the use of an improved system of management regimes of the microclimate in the protected ground on the basis of programmable smart relays

Keywords: power consumption, temperature-humidity conditions, microclimate

Is considered a tool of marketing communications - personal selling. Describes the basic theoretical aspects of the system of integrated marketing communications, differences of classical and integrated complex of the promotion, analysis of a modern condition of integrated marketing communications. Allocated significance, main features, the uniqueness, the advantages and disadvantages of personal sales. Defined are the main differences between personal sales from the other instruments of the complex progress, as well as the identification of the characteristics of personal sales in the integration with other promotion tools of the marketing complex. Describes the use of personal sales, the system of integrated marketing communications. Allocation of the basic purposes and tasks of the personal sale in a complex of promotion and in integrated marketing communications.

Keywords: Complex promotion, marketing communication, integrated marketing communications, personal selling, personal contact

Defined criteria for identification of defect parameters, on the basis of the analysis of the different modes of own fluctuations, with the use of finite element modal calculation console corpulent model of a rod with a single defect. Developed finite element model of a universal complex . Considered corpulent (3-d) model on the basis of 3D finite element Solid92. When solving the problem considered on 26 oscillation modes depending on the size of the defect and its location.

Keywords: Damaged, defective, swing, cantilever, frequency

The task of identification of defects in rods with different variants of fastening. In the basis of lies method parameter identification based on an analysis of the frequencies and parameters of natural modes of the structure. Built model of the rod design has defects fluctuations, using finite element of the complex 

Keywords: Defect, damage, rod, the oscillations of the cantilever rod