The introduction of information modeling technologies (TIM) into construction practice is irreversible all over the world. The effectiveness of the use of TIM has been proven at all stages of the life cycle of capital construction facilities: at the pre-design phase, at the stages of design, construction, operation, repair, reconstruction, de-installation and disposal. A variety of software for digitalization of construction allows you to choose the optimal product for a specific type of task. Until recently, most of the Russian information modeling technology market belonged to software products of foreign IT companies. Due to the changed conditions, there is a forced transition to domestic TIM systems. The challenges that arise in this case require joint actions by government agencies, software developers in the field of TIM, construction companies and educational organizations.

Keywords: information modeling technologies, BIM technologies, the life cycle of a capital construction facility, construction, import substitution, training of specialists, Russian TIM systems

This article analyzes the main causes of fatal injuries in the construction industry of the Russian Federation and a number of other foreign countries, including falls from heights, electric shock, injuries associated with the use of construction machinery and mechanisms, as well as exposure to harmful substances. In conclusion, the article highlights the importance of joint efforts by employers, employees and regulators to create a safer and healthier work environment in the construction industry. The implementation of the preventive measures described in the article can significantly reduce the risk of accidents and improve the well-being of employees.

Keywords: construction industry, industrial injuries, accidents, causes of injuries, working conditions, occupational risks, working at height, occupational safety, environmental factors, workplace organization, training

Reinforced concrete is the most common material in construction, this is due to its high performance and consumer characteristics. Despite a number of its positive characteristics, concrete has a negative property, its hygroscopicity. In the structure of concrete is a large number of micropores, cracks and capillaries, which contribute to the spread of moisture throughout the structure. This leads to the destruction of concrete, corrosion of reinforcement. Waterproofing is an important aspect of building construction and maintenance. It helps prevent moisture damage that leads to costly repairs and structural failure over time.

Keywords: concrete waterproofing, waterproofing system, polymer membrane, geocomposite fabric, liquid waterproofing membrane, penetrating waterproofing

The article discusses the planning and commissioning of an autonomous field located on permafrost. Most of the oil and gas fields are located in permafrost areas. The development of such deposits is costly, as it creates the need to prevent the thawing of permafrost. Commissioning works are the final stage of construction and installation works. The CW is difficult in conditions of permafrost. In permafrost conditions, problems may arise with starting the installed equipment.

Keywords: commissioning, permafrost, field, installation, drilling, oil industry, oil and gas industry, project, freezing, maintenance

The article is devoted to the issue of making organizational and technological decisions when the stock of information for alternatives to choosing the required tasks is either very small, or they are changing drastically. Since it is not easy to make an organizational and technological business decision due to the fact that it is not clear what the result will be, it is proposed to use game theory in conditions of uncertainty. What kind of decision will be made and which of the available strategies the designer will adopt depends on what economic effect will be obtained as a result of the implementation of the organizational and technological solution being developed. Game theory is a special class of mathematical models for decision-making under specific conditions. By choosing solutions in the wake of uncertainty, game theory formalizes possible knowledge about the course of action of the participants in the game in certain conflict situations and allows you to mathematically substantiate knowledge about a rational course of action in certain conditions. When constructing construction projects in environmentally unfavorable conditions, the risk matrix is compared and the best option for the development of a construction project is determined.

Keywords: construction and technical expertise, reliability, organizational and technological solutions, diagnostic methods, efficiency.

This paper examines the problems and obstacles that arise during the implementation of investment projects in the field of capital construction, between the customer and the general contractor (a subsidiary of the customer). To solve the problems, it is proposed to develop specific measures to modernize the investment and construction activities of the customer company, in accordance with the economic development strategy adopted in Russia, based on digitalization. Information systems and technologies offer great opportunities for the development of various aspects of economic activity. One of them is information systems for managing investment projects. As a result of the work, the authors formulated the main directions of development and proposed solutions for modernizing the investment and construction activities of the customer company.

Keywords: investment and construction activities, investment project, industrial construction, customer, general contractor, information systems and technologies

" The article discusses organizational and technological solutions for the installation of hinged ventilated facades, which are aimed at: ensuring the efficiency of work; increasing labor safety and productivity, reducing the cost of installation work, eliminating wasteful consumption of all types of resources used, using progressive methods of organizing work; use of modern means of mechaniza-tion and automation. Organizational and technological solutions in the design of ventilated curtain walls were optimized in three stages. The main problem identified in this article is that in modern construction, with a wide variety of structures available, facade systems are selected without appropriate organizational, technologi-cal, and economic justification, mainly relying on the experience of previous construction projects. Therefore, the problem of lacking reliable tools for determining the effectiveness of various organi-zational and technological solutions for facade work production at the planning stage of the object's life cycle can be formulated."

Keywords: hinged ventilated facades, organizational and technological solutions, organiza-tional and technological documentation, technological map, thermal insulation

The article provides research on the issues of effective construction of concrete structures of various functionality. The purpose of the article is to study the features of the processes of effective construction of concrete structures of various functionality in construction. To achieve the set goals, the tasks of conducting an analytical review on the issue, dedicated to the production of concrete with specified properties for monolithic concrete structures, were solved in order to reduce the influence of external temperature factors on their properties. Modern technologies for the construction of concrete structures were analyzed: fiber-reinforced concrete, “smart” concrete, as well as modification methods to improve the properties of concrete structures.

Keywords: construction, concrete, concrete structures, functionality, properties, construction.

This article discusses the problem of determining the parameters of the underground structure during large-block construction. The construction of buildings from large modules is a method of building construction, which is based on the use of ready-to-assemble modules of large sizes. This construction method allows you to significantly speed up the process of building construction, reduce construction costs, and ensure a high level of quality and functionality of structures, primarily due to the fact that these structural blocks are built in factory conditions. They can be made of various materials such as concrete, steel or composite materials. These modules can include not only walls and partitions, but also floors, ceilings, electrical wiring, plumbing and other elements, which reduces the assembly time on site.

Keywords: large-block construction, construction of the underground part of a large-block structure, building structures, technologies and organization of construction production.

The article discusses issues of improving the quality and safety of pedestrian and vehicle traffic in underground linear structures. The main parameters of traffic safety in tunnel-type transport structures are considered. The scope of application of luminescent and retroreflective materials in the construction and operation of concrete and asphalt concrete pavements has been determined. Recommendations are given for the use of special luminous materials in construction practice.

Keywords: concrete, asphalt concrete, reflective coatings, luminescent materials, traffic safety

The purpose of this study is to develop a survey methodology that allows you to determine the composition of the common property of an apartment building, which is used in the operation of non-residential premises. In the process of theoretical research, analysis methods and results of field observations were used. The results of this study are the classification of non-residential premises that are not part of the common property of an apartment building, a list of elements of an apartment building to be examined to assess their use in the operation of non-residential premises, recommendations to a specialist on the list of documents necessary for this survey. These results are of practical importance for specialists in the field of inspection of buildings and structures when resolving disputes in the practice of operating apartment buildings and non-residential premises that are not part of the common property of a residential building.

Keywords: non-residential premises, classification of non-residential premises, survey methodology, apartment building, common property, list of common property elements, composition of common property, operation, housing stock

Wood as a building material has ancient roots and a long history of use. With the development of technology and the desire to live in better environmental conditions, interest in using wood to construct multi-story buildings is growing. This article is devoted to the prospects for the development of wooden multi-story buildings in Russia, in particular with the use of CLT panels, the popularity of which is growing all over the world. Comparative, statistical and logical analyzes were used as research methods. The article discusses modern methods and technologies for the construction of multi-story wooden buildings, including their advantages in terms of ecology, energy efficiency and design, conducts a comparative analysis of buildings made of reinforced concrete and CLT panels, and proposes a technological scheme for the reconstruction of buildings using CLT panels, including adding additional floors. Challenges and prospects for further development of this technology are highlighted, strategic solutions are proposed to reduce the cost of CLT panels

Keywords: clt-panels, wood construction, wooden structures, reconstruction, renovation, high-rise wooden construction

The article deals with the problem of education and management of construction waste. The data on the increase in construction volumes and, as a result, an increase in the amount of waste in Russia are presented. The main sources and types of construction waste are analyzed, their classification according to the degree of danger. Traditional and modern methods of waste disposal, such as burial, recycling, incineration, are discussed. The conclusion is made about the need to improve environmental culture in the construction industry and improve waste management legislation.

Keywords: construction waste, construction debris, waste disposal, recycling, environmental culture, waste legislation

The article analyzes modern approaches and technologies for recycling and recycling of building materials. Such types of waste as reinforced concrete, brick, glass, wood, plastic, etc. are considered. Special attention is paid to innovative methods of processing to obtain secondary raw materials (recycling). It is shown that the most promising technologies are the crushing of concrete, brick and reinforced concrete for reuse in construction, the melting of scrap metal, glass and plastic, the processing of wood waste into slabs and fuel. There is an insufficient level of application of innovative solutions in Russia. A set of measures has been proposed to improve the efficiency of construction waste disposal: the introduction of advanced technologies, the construction of waste recycling plants, the adoption of a targeted state program, and the improvement of environmental culture.

Keywords: waste, construction debris, Russia, secondary raw materials, reuse, environment, recycling, burial, recycling

The article discusses the design features of wooden buildings constructed from cross laminated timber panels (CLT). CLTis a new material widely used in wooden house construction. The panels are used for the construction of multi-storey buildings and replace traditional frame and cobblestone wooden houses. The article analyzes the advantages of using CLT in modern construction, discusses various types of joints, such as butt joints, corner joints, as well as their advantages and disadvantages. Special attention is paid to panel mounting methods that ensure the reliability and durability of the structure.

Keywords: wooden structure, wood, cross-laminated timber, CLT panel, nodal connection, connection system

The prospect is explored to arrange for incoming and ongoing quality control using digital tools and devices, including those supplanting conventional ones. The paper underscores the importance of integrating digital quality control technologies and BIM technologies as a means to identify potential defects and justifies the relevance of improving the gesture control code for quality control purposes. It further summarizes the quality control techniques and procedures and highlights an opportunity to develop digitalized quality control charts based on effective conventional documents.

Keywords: integration of BIM, VR and АR technologies, laser scanner, ongoing quality control chart, digital quality information model

The problem of building a model of an intelligent system for continuous monitoring of the density of asphalt concrete mixture for vibrating rollers is considered. The methodology and theoretical foundations of the construction of such systems for road machines were considered by the author earlier in the author's publications. Four models of functional dependencies of compaction quality indicators on variable dynamic parameters of the system are proposed. An algorithm that implements the proposed method is presented, as well as scientific results obtained on the basis of measured signals of vibration parameters in a field experimental study during the construction of the upper layer of asphalt concrete pavement of a highway. Scientific results were obtained on the basis of the analysis of data of variables in the time domain.

Keywords: intelligent system, fuzzy neural network, asphalt roller

The article is devoted to the use of reinforced soils in the base of pavements of highways located in the I road-climatic zone. The features of the operating modes of reinforced foundation soils are considered, and their physical and mechanical characteristics with various combinations of mineral and polymer modifiers are determined. The authors analyze the advantages and disadvantages of using reinforced soils. The article also discusses the design and construction of roads using reinforced soils.

Keywords: highway, road pavement, foundation, soils, reinforced soils, modifiers

The relevance of the issue of variant design is considered, taking into account the analysis of previously applied solutions. The concept of installation manufacturability of objects is revealed, its component properties are substantiated. A table of the hierarchy of installation manufacturability properties has been generated. The functions of each level of the property hierarchy are disclosed. The weight indicators of the criteria were calculated using an expert survey. a formula for a complex indicator of installation manufacturability was obtained. A hypothesis has been put forward about the quantitative assessment of the levels of installation manufacturability.

Keywords: manufacturability, installation manufacturability, levels of hierarchy of installation manufacturability, weight of indicators of properties of installation manufacturability, installation of steel structures

The article discusses the use of organic binders to modify the properties of cement soils. The scope of application of cement soils in construction practice, including the construction of highways, is considered. The influence of the use of organic binders as a complex additive that modifies the strength characteristics of cement soils has been studied. The influence of the use of complex modifiers and additives on the frost resistance and water permeability of cement soils has been determined.

Keywords: cement soil, organic binder, highway, working layer, frost resistance, modifiers

Technology of jet-grouting is a method of strengthening weak or heavily watered soils by pumping high-pressure cement slurry into the well to break the structure of the soil and simultaneously stirring its particles with cement slurry. The result is a ground-cement mass which has predefined improved strength and deformation characteristics. Technology of jet-grouting has a great potential for development and application in various construction industries, such as buildings, roads, bridges and other structures under various geological conditions. The development of jet-grouting technology won't only expand its application, but can improve competitiveness in the construction services market.

Keywords: recycling, reinforced concrete, secondary crushed stone, construction waste, crushing equipment.

The article deals with the issues of major repairs of rooms for radiation diagnostics in medical institutions, which is becoming more and more relevant in modern conditions. Functional diagnostics plays a key role in early detection of diseases, correct diagnosis and effective treatment of patients. With the development of technology and the advent of high-tech diagnostic equipment, there is a need to upgrade medical institutions to integrate such equipment. The study, conducted on the basis of an analysis of regulatory and technical documentation and scientific papers, highlighted the main stages of major repairs of radiation diagnostics facilities, identified the main participants in these stages. Organizational charts have also been developed for each stage, which emphasize the importance of coordination between all project participants, including builders, engineers, architects and medical specialists. The implementation of such schemes helps to minimize time and financial costs, ensures the implementation of all necessary requirements and standards, and guarantees the high quality of the work performed. As a result, we receive an organized repair process that allows medical institutions to effectively use new diagnostic equipment to improve the quality of medical services and improve the diagnosis and treatment of patients.

Keywords: major repairs, healthcare facilities, radiation diagnostics facilities, medical organization, project documentation

The problem of increasing consumption of heat and energy resources in the high-rise residential sector in the conditions of dense urban development becomes more relevant every year both for its population and for management companies. In order to reduce operating costs, to reduce the dependence of engineering systems of high-rise residential building on urban infrastructure, it is proposed to introduce some energy-efficient organisational and technological solutions in the designed apartment building. In the course of the study, on the example of a high-rise 25-storey residential building in the city of Rostov-on-Don, a comparison of operating costs of thermal energy for heating with the use of energy-saving materials and structures, and costs in typical conditions of construction. The results of this work will allow, from a practical point of view, to analyse the feasibility of using such energy-efficient building envelopes and materials as foil PIR-insulation, low-emission four-chamber glazing, "green" roofing in high-rise housing construction.

Keywords: energy efficient building envelopes, heat consumption, heating costs, high-rise apartment block, economic analysis, sustainable construction

This article discusses several ways to determine the calculated lengths of steel columns in the plane of the frame. By analyzing existing techniques, the most successful method of selecting the calculated lengths for steel columns in a free multi-storey frame was determined. Taking into account the non-standard case of fastening crossbars to the considered section in the frame of the overpass, using the LIRA CAD PC, as well as the Crystal module (implemented in SCAD), the loss of stability of equally loaded elements in the most sensitive area is clearly shown.

Keywords: Euler's formula, loss of stability, coefficient of calculated length, calculated length, coefficient of stability margin, finite elements

The concept of digitalization of the construction organization project (POS) is presented, which is based on its close connection with the construction schedule. The place of the POS in the digital model of the building at the project stage (PIM) is considered. based on its digitalization, taking into account the relationship between information modeling at the project stage (PIM). The main problems that may arise when implementing the digital version of the POS in the general information model at the project stage are identified.

Keywords: BIM, TIM, POS, digital model, calendar schedule, construction organization