In this article is reviewed the nature of organic hybrid nanocomposites. Promising directions in the field of organic hybrid nanocomposite materials will be methods for the synthesis of multicomponent materials, as well as the type of "net net" and "host-guest". The fundamental problem with the chemistry and physics of nanocomposites is dependent "structure-property". Solving this problem will move from research materials to their purposeful design.

Keywords: nanocomposite sol-gel technology, synthesis, nanoparticles.

The paper provides information on the results of ordination analysis of Don basin steppes

Keywords: ordination, Don basin, steppes

At present an important role in solving energy conservation problem is assigned to thermal pumping plants (TPP). Using processes of evaporation and condensation of easily boiling liquid circulating in the system they extract low potential heat from environmental objects and provide heat supply for buildings, constructions, greenhousee and so on. Artificial sources of low potential heat for TPP of different capacity can be, for instance, ventilation air and exhaust gases, circulating and waste water,ground. Energy efficient reasonability of TPP use in the system of water disposal for the town of Novocherkassk in Rostov region is considered. Calculations indicate that there is a technical potential to replace a boiler house operating on expensive gas fuel and emissing into the atmospere more than 850 t of carbon dioxide - greenhouse gas - with ecologically clean TPP, one of which uses heat of waste water and the other - heat of ground.

Keywords: thermal pumping plant, renewable sources, energy conservation, evaporation, condensation, waste water, ground

This paper considers basic element of device of energy storage which is a piezoelectric generator (PEG) of cylindrical form with the attached inertial mass. A finite element modeling of the device operation is carried out during active load in the external circuit. The main purpose of the operation is to compare the output potential and frequency characteristics of the device known in the literature models of systems with concentrated parameters. On the basis of these models, we can receive the analytical dependence of parameters of PEG with its geometric characteristics and mechanical properties of the used materials. However, the question of the range of applicability of these formulas is still open. In this paper, based on the numerical analysis of finite element models of PEG in package ANSYS, we obtained comparison with the analytical formulas that show the values of some parameters of simplified models and set the boundaries of their applicability.

Keywords: energy storage, PEG, piezoceramics, effective mass, resonant frequency, FEM

Problems of service and repair of bridge constructions of a network of the irrigation canals which are on balance of managements of melioration are considered. The description and functionality of the automated imnformatsionny system developed by authors, allowing to carry out the account and monitoring of technical condition of bridge constructions in the territory of the Rostov region is provided.

Keywords: The meliorative channel, bridge construction, durability and operational reliability of bridge moving via water carrying out channels, monitoring of a condition of the bridge moving, the automated information system

The method of coding of the geometrical information is offered at the task of executive mechanisms on the basis of use of the set set of spatial primitive things and their orientation in mobile systems of co-ordinates. The method of a designation of geometrical models of mechanisms of robots is offered. One of advantages of the developed method of representation of geometrical models of kinematic chains, possibility of more exact task of a spatial configuration of manipulators by means of use of a considerable quantity of central points and various position of volume primitive things concerning a constructive plane is.

Keywords: Mechanisms of manipulators, geometrical models, virtual modelling of movements of robots

History share of insurance business in the Province of the Don, the characteristic four stages of development process, the analysis in general and the specific activity of sixteen joint campaigns, including foreign, on the Don in the late XIX - early XX centuries. ("New York", "Urbain", "Ekvitebl"). The social composition of the policyholders, insurance forms discounts logic of competition  

Keywords: insurance organization of insurance business corporate insurance insured event insurance discount insurance premium insurance rates insurance capital

In the article describes the program realization of calculation unit pneumatic measuring system. The program is implemented in the languages ​​of IEC: CFC and ST. Algorithm written with the possibility of future use in systems that differ from described in the article. The developed algorithm allows to measure temperature directly using computing power PLC and get the result in the final form, without any changes on the part of the operator.

Keywords: pneumatics, temperature, airflow, algorithm of temperature measuring, temperature measurement, Codesys, CFC, ST

In this paper a modification of logic element DC LUT FPGA is proposed for the purpose of the acceleration of diagnostics. Simulation of proposed modification was performed in the system NI Multisim 10 by National Instruments Electronics Workbench Group. Evaluation of hardware costs is also given.

Keywords: logic element, DC LUT, FPGA, diagnosis, reliability

The article is considered the ecological and economic rationale for the use and application of alternative fuels from MSW (RDF) to produce cement. The economic efficiency of RDF at JSC "Sebryakovcement" at the current rate of natural and secondary energy. The aim of our work is to develop effective thermal and hardware solutions optimized commercial and environmental solutions for the development of the use of solid waste in the cement industry.

Keywords: alternative fuels, municipal solid waste (MSW), RDF, cement industry, environmental safety.

The article is described the environmental and economic feasibility of the use of fossil fuels on RDF. The opportunity of introduction of alternative fuels, as an essential part of maintaining a balance of market equilibrium in the competitiveness of the products of the company "Sebryakovcement". The calculation of potential possibilities of processing of waste RDF as a necessary component to maintain the balance of market equilibrium and competitiveness of enterprise "Sebryakovcement." Calculation of the potential waste in RDF

Keywords: alternative fuels, municipal solid waste (MSW), RDF, cement industry, environmental safety.

The research of influence of periodical signal discontinuity on spectrum form is considered in the article. The numerical modeling of the system of discontinuous signals is performed. The spectrum of the system built from time discreet sampling is analyzed. The plots of the sample correlation coefficient between spectrums of continuous and discontinues signals are shown in the article. The research is needed for the development of digital measuring system for quartz plates frequency detecting.

Keywords: amplitude signal spectrum, discontinuous signal, quartz plates

The atomic structure of bimetallic nanoparticles of Pt-Ag composition, which are the part of metal-carbon electro-catalysts PtAg/C, is studied by means of EXAFS spectroscopy using the suggested technique. These materials have been prepared by methods of consistent and simultaneous deposition of Ag and Pt atoms from aqueous ethylene glycol solutions of their salts with subsequent acid treatment. The values ​​of the structural parameters of the near environment of platinum atoms are determined. The nature of the distribution of components in nanoparticles is established. Cluster models of nanoparticles are constructed. The fraction of Pt atoms in the working shell and its dependance on preparation methods in each case are determined.

Keywords: Metal-carbon electrocatalysts, bimetallic nanoparticles, Catalysis, Platinum, X-ray absorption spectroscopy, atomic structure

The article is devoted to modelling of process of decision-making in difficult systems in the conditions of total uncertainty. The problem is formulated on the basis of synthesis of concepts of the control theory and decision-making, the theory of fuzzy sets and the fuzzy logic, the theory of hierarchical multilevel systems, the utility theory and the theory of games. The given concept expands possibilities of the account uncertainty the various nature, typical to mathematical description of the surrounding validity. Problems of search of decisions in an fuzzy hierarchical control system are designated. The way of the description and finding of alternative decisions in multilevel difficult systems is offered in given article. The algorithm is based on information processing in the form of fuzzy intervals taking into account two kinds the politician conservative and aggressive on the basis of criteria «maxmin» and «minmax». The method of projection on individual interval is used for comparison of the fuzzy intervals presented on various dimension scales. The example showing work of algorithm of a choice of two groups of alternatives is resulted: optimistic and pessimistic on a level of hierarchies of the purposes in the conditions of total uncertainty.

Keywords: Difficult system; decision making, fuzzy interval, the control decision; total uncertainty

To improve the quality of developed software for the controller is proposed to take into account the principles of programming in FBD and CFC. Gives practical recommendations for the use application of. Especially, this approach is acquitted for complex systems of automatic control and regulation of high risk. The proposed method reduces the requirements for qualification of personnel, increases productivity in extreme situations, reduces the possibility of errors in the adjustment programs.

Keywords: Programming principles, identity numbering algoblocks similar algorithms, the in-between software cleat, the principle of non-rigid numbering, quality and reliability of software.