With the use of pulsed laser deposition and carbothermal synthesis а photosensitive structure on the basis of the Schottky barrier Au/ZnO(nanorods)/ZnO(film)/ZnO(nanorods)/Au was obtained. The parameters of the carbothermal method of synthesis of nanorods ZnO were optimized. Under directly applied bias of 7V current sensitivity of luminous flux for this photodetector is observed in the UV and visible regions of the spectrum, and is 0.14 A/W - for 325 nm and 0.18 A/W - to 405 nm, which means that this structure has the ability of potential applications in various fields for the control of UV radiation (for example, for the monitoring of solar UV radiation, control of UV radiation in air and disinfecting water devices).

Keywords: ZnO nanorods, Schottky barrier, photodetector, photosensitivity

ZnO nanorod arrays have been synthesized on silicon wafers by chemical vapor deposition (CVD) technique with different  temperature modes, without metal catalyst.  With this method   vertically aligned ZnO nanostructures  were grown at the quite low temperatures.  Modification of the method allowed to place silicon substrates in areas with different  ratios of concentrations of the molecules in the vapor phase. Photoluminescence spectroscopy and electron microscopy studies have shown that morphologies and optical properties of nanorods depends on different ratios of concentrations of the molecules in the vapor phase.

Keywords: ZnO nanorods,chemical vapor deposition (CVD), photoluminescence

The arrays of ZnO nanorods were obtained on the sapphire substrates by means of pulsed laser deposition under the high pressure of argon. The conditions of synthesis were optimized, and their influence on the morphology of  ZnO nanostructures were revealed. It is shown that the concentration of oxygen vacancies in ZnO nanorods can be changed by regulation of the synthesis temperature from 850 to 915 °. This process can be controlled by the ratio of intensities of the photoluminescence emission in the visible and ultraviolet regions. So, it allows to create nanostructures for UV photodetectors or chemosensors depending on the temperature choice.

Keywords: ZnO nanorods, laser deposition, PLD, photoluminescence

The method of application of fuzzy logic to solve the problem of spatial planning using geographic and information systems is described. The spatial arrangement of objects on the map is used as input factors of the solution, to find which a model of the spatial descriptions of objects using a bitmap representation is constructed. The way of formalizing fuzzy judgments about positional relationship of objects and the system of inference making based on the fuzzy logic methods is developed. An example of using the method described in this article to determine the sanitary protection zone of industrial waste landfill in the territory of the Republic of Bashkortostan is given

Keywords: fuzzy logic, geographic information systems, the problem of territorial planning, disposal of industrial waste, protection zones

This paper outlines the implementation of computer model of second-order visual mechanisms that are specific to spatial contrast modulations, and represents the results of testing the model. Computer simulation is based on "Filter-Rectify-Filter" model with some important additions. The inhibitory parts of receptive field of simulated mechanism are non-selective to orientation and spatial frequency of texture elements. Texture modulated by orientation or spatial frequency does not reduce flank inhibition and does not activate the mechanism. Unmodulated texture  also does not cause activation of the filter because the flanking inhibition will be equal to or exceed the excitation. However, increasing the contrast in the center and reduction it on the flanks leads to the activation of the second order mechanism.

Keywords: Second order visual mechanisms, image filtering, texture, spatial modulation, computer simulation

The results of research of raw materials of the logs production for timber construction are considered in the article. Length of logs (for 6 meters assortment), diameter of logs (model logs) and shape of butt (an average shape factor of butt) were studied. The model log is a volume of cylinder which is equal to a calculated volume of logs. The theoretical laws of the random variable for these values are found. The Research was conducted at LLC "Biogran" in Petrozavodsk, Republic of Karelia.

Keywords: Woodworking, cylindering, technological line, wood costraction, factors, length of a log, diameter of a log, butt

The article describes peculiarities of modern syntax parser systems and problems originating in text analysis. As a result of comparative analysis the authors propose a unified approach to processing of unstructured texts in Russian and English which combines morphology and syntax processing. The developed syntax analysis system, using verbs’ valency dictionary, samples of minimal structural schemes of sentences and samples of conjunctions, allows choosing predicative structures of sentences in the text, realizing initial semantic analysis due to semantic content of predicate’s actants and building trees of syntactical subordination of sentences. The derived trees hold elements of tree of constitutives and tree of dependences. The proposed samples and rules organization allows resolving some of the problems of modern parsers. And the use of verbs’ valency dictionary allows reducing the number of sentences syntax analysis variants.

Keywords: automatic text processing; syntax parser; morphological analysis; structural text elements

In this paper is offered hydraulic sensor to measure the kinematic, power and energy parameters. Developed scheme and the principles of the hydraulic sensor.  Identification  on the special flow lab with real modes of the device is determined by its performance in different conditions. Approximation of the results received dependences flow and pressure drop characteristics on the speed and entrance pressure, allowed more correctly assess and describe the operation of the hydraulic sensor over the entire range of speed and entrance pressure.

Keywords: hydraulic sensor, spilling method, flow and pressure drop characteristics, multifunction control unit.

The temperature dependencies of the main parameters of p-channel MOSFET model in a temperature range 20 ... 300 K are measured. The universal formal four-parametric model, which allows approximating all experimental temperature dependencies with the relative error less than 1 % is proposed. The model is intended for the MOSFETs which are applying in low-noise amplifiers of the radio-receiving devices of an optical and infrared range on astronomical satellites, radio telescopes and space observatories. The presented results can be used to simulate the temperature modes of MOSFET amplifiers in SPICE-type electronic simulators. The solution of this problem will predict uptime device when the temperature changes in the cases of emergency or extraordinary situations and also will allow optimizing the choice of refrigerant and increasing the reliability of the amplifier in the conditions of cryogenic temperatures.

Keywords: MOSFET, MOSFET parameters, cryogenic temperature, parameters measurement, temperature dependencies

The problem of efficient use of lubricants in service of railway technology, based on a system for the collection of used oil and re-use them after regeneration. The analysis of the consumption of lubricants and identify possible potential resource - the volume of used oil and the resulting volume of recovered oil.

Keywords: oils, operation of transport equipment, used oil, used oil collection, regeneration

In this paper a systematic study of individual single-walled and multi-walled carbon nanotubes was performed by Raman spectroscopy and high-resolution electron microscopy. We have presented the geometrical and electronic structure analysis on the examples of two tubes: individual single-walled and double-walled nanotubes. The role of different environmental effects and their influence on the final structure assignment are discussed. Moreover, we have shown that the Raman spectroscopy gives reliable estimations of the nanotube diameters and the conductivity. Given a non-destructible character of Raman spectroscopy, we may conclude that it is one of the most efficient methods for structure analysis of carbon nanotubes.

Keywords: Carbon nanotubes, Raman spectroscopy, electron microscopy

This article describes the model of the pseudorandom sequences (PRS) generator developed in OrCAD program suite.The described model is applicable for radio systems modules circuits simulation that are using in the operation a PRS. The PRS generator implementation in OrCAD make possible to change PRS parametres immediately in the program, without using other software. A model specificity is that it is parametrised. Parametrization facilitates model control and that is reduce to a minimum necessary manipulations for changing of PRS type. The model is constructed on the basis of circuitry implementation of the linear feedback shift register (LFSR). For adjustment of model it is enough to instal code words setting starting state a LFSR, parametres of a signal of a clock source and to specify register tap output. As an example, used a 16-bit LFSR to create maximum length PRS, tap sequence {0, 5, 9, 13}. Emulation results are presented.

Keywords: pseudorandom sequence, PRS generator, LFSR, OrCAD, circuit simulation

The represented approach of dynamic process modeling is based on the technology of automatical semantic text analysis. An associative network is forming during text processing. Its key notions, including  lexical and psycholinguistic markers of the analyzed process, are ranked by theirs semantic weight. The weight being multiplied by marker status value at the scale of “good-bad” gives its contribution to the process stage characteristic. Transformation of the accumulated for all of the markers process characteristic from one period of time to another one is characterize a direction of the process.

Keywords: automatical text processing, associative (homogenous semantic) network, process dynamic modeling, social processes, lexical and psycholinguistic markers

The article discusses a method for optimizing the synthesis of digital state machines for solving tasks of search patterns with masks on FPGA using automatic models. Standard methods for the synthesis of the FPGA don't optimize digital state machines, but only optimize the placement of logic elements on the chip. The method of vectoring states involve the decomposition the structure of the machine and the combining the variety of states to the vertex-array of states. The states in the vertex-array is controlled by special state machine. This simplifies the addressing to the heights of states of the graph , and optimizes logical structure of machine. The number of states of the digital machine remains unchanged. Vectorization of states is simplifying the synthesis and control of state machine and reduces the number of logical elements.

Keywords: digital state machine, graph of digital state machine, synthesis of digital state machine, FPGA, reconfigurable computing system, pattern search, vectoring states of digital state machine.

Одним из важнейших факторов, исключающих возникновение дефектов типа пор, расслоений, участков с неполной полимеризацией связующего в формуемой высоконагруженной полимерной композитной конструкции, является управляемость процесса во всем объеме композита. Для обеспечения однородности процесса полимеризации связующего предложен метод многокритериальной оптимизации процесса на основе математической модели, связывающей процессы распространения тепла и кинетики полимеризации. Система связанных уравнений процесса, учитывающая экзотермическое тепло, выделяемое при полимеризации термореактивного связующего, изменение теплоемкости и теплопроводности композита при фазовых переходах от жидкого к гелеобразному и, далее, к твердому состоянию, точную геометрию технологической системы, включая прессформу, а также интенсивность тепловыделения независимо управляемых нагревателей, реализована в виде конечноэлементной модели. Предложенный метод синтеза закона оптимального управления нагревателями, использующий метод множеств Парето, проиллюстрирован на примере полимеризации разностенной композитной конструкции, формуемой из стеклопластика.

Keywords: Композиционные материалы; Процесс полимеризации; Оптимальное управление; Кинетические уравнения; Уравнения в частных производных в задачах управления и оптимизации, Конечно-элементное моделирование, Фронт Парето