In this article is reviewed the nature of organic hybrid nanocomposites. Promising directions in the field of organic hybrid nanocomposite materials will be methods for the synthesis of multicomponent materials, as well as the type of "net net" and "host-guest". The fundamental problem with the chemistry and physics of nanocomposites is dependent "structure-property". Solving this problem will move from research materials to their purposeful design.

Keywords: nanocomposite sol-gel technology, synthesis, nanoparticles.

The paper provides information on the results of ordination analysis of Don basin steppes

Keywords: ordination, Don basin, steppes

At present an important role in solving energy conservation problem is assigned to thermal pumping plants (TPP). Using processes of evaporation and condensation of easily boiling liquid circulating in the system they extract low potential heat from environmental objects and provide heat supply for buildings, constructions, greenhousee and so on. Artificial sources of low potential heat for TPP of different capacity can be, for instance, ventilation air and exhaust gases, circulating and waste water,ground. Energy efficient reasonability of TPP use in the system of water disposal for the town of Novocherkassk in Rostov region is considered. Calculations indicate that there is a technical potential to replace a boiler house operating on expensive gas fuel and emissing into the atmospere more than 850 t of carbon dioxide - greenhouse gas - with ecologically clean TPP, one of which uses heat of waste water and the other - heat of ground.

Keywords: thermal pumping plant, renewable sources, energy conservation, evaporation, condensation, waste water, ground

This paper considers basic element of device of energy storage which is a piezoelectric generator (PEG) of cylindrical form with the attached inertial mass. A finite element modeling of the device operation is carried out during active load in the external circuit. The main purpose of the operation is to compare the output potential and frequency characteristics of the device known in the literature models of systems with concentrated parameters. On the basis of these models, we can receive the analytical dependence of parameters of PEG with its geometric characteristics and mechanical properties of the used materials. However, the question of the range of applicability of these formulas is still open. In this paper, based on the numerical analysis of finite element models of PEG in package ANSYS, we obtained comparison with the analytical formulas that show the values of some parameters of simplified models and set the boundaries of their applicability.

Keywords: energy storage, PEG, piezoceramics, effective mass, resonant frequency, FEM

The method of coding of the geometrical information is offered at the task of executive mechanisms on the basis of use of the set set of spatial primitive things and their orientation in mobile systems of co-ordinates. The method of a designation of geometrical models of mechanisms of robots is offered. One of advantages of the developed method of representation of geometrical models of kinematic chains, possibility of more exact task of a spatial configuration of manipulators by means of use of a considerable quantity of central points and various position of volume primitive things concerning a constructive plane is.

Keywords: Mechanisms of manipulators, geometrical models, virtual modelling of movements of robots

In the article describes the program realization of calculation unit pneumatic measuring system. The program is implemented in the languages ​​of IEC: CFC and ST. Algorithm written with the possibility of future use in systems that differ from described in the article. The developed algorithm allows to measure temperature directly using computing power PLC and get the result in the final form, without any changes on the part of the operator.

Keywords: pneumatics, temperature, airflow, algorithm of temperature measuring, temperature measurement, Codesys, CFC, ST

Simulation and method of classification of technical condition high-voltage the mekhatronics of modules of the movement, allowing by results of control of electrodigit activity and skrednekvadratichesky value of vibrospeed are presented, to refer current state of object to one of classes of diagnoses

Keywords: High-voltage mekhatronics module, fuzzy-model of classification of technical condition, electrodigital activity, vibrospeed

The article is considered the ecological and economic rationale for the use and application of alternative fuels from MSW (RDF) to produce cement. The economic efficiency of RDF at JSC "Sebryakovcement" at the current rate of natural and secondary energy. The aim of our work is to develop effective thermal and hardware solutions optimized commercial and environmental solutions for the development of the use of solid waste in the cement industry.

Keywords: alternative fuels, municipal solid waste (MSW), RDF, cement industry, environmental safety.

The article is described the environmental and economic feasibility of the use of fossil fuels on RDF. The opportunity of introduction of alternative fuels, as an essential part of maintaining a balance of market equilibrium in the competitiveness of the products of the company "Sebryakovcement". The calculation of potential possibilities of processing of waste RDF as a necessary component to maintain the balance of market equilibrium and competitiveness of enterprise "Sebryakovcement." Calculation of the potential waste in RDF

Keywords: alternative fuels, municipal solid waste (MSW), RDF, cement industry, environmental safety.

The research of influence of periodical signal discontinuity on spectrum form is considered in the article. The numerical modeling of the system of discontinuous signals is performed. The spectrum of the system built from time discreet sampling is analyzed. The plots of the sample correlation coefficient between spectrums of continuous and discontinues signals are shown in the article. The research is needed for the development of digital measuring system for quartz plates frequency detecting.

Keywords: amplitude signal spectrum, discontinuous signal, quartz plates

The atomic structure of bimetallic nanoparticles of Pt-Ag composition, which are the part of metal-carbon electro-catalysts PtAg/C, is studied by means of EXAFS spectroscopy using the suggested technique. These materials have been prepared by methods of consistent and simultaneous deposition of Ag and Pt atoms from aqueous ethylene glycol solutions of their salts with subsequent acid treatment. The values ​​of the structural parameters of the near environment of platinum atoms are determined. The nature of the distribution of components in nanoparticles is established. Cluster models of nanoparticles are constructed. The fraction of Pt atoms in the working shell and its dependance on preparation methods in each case are determined.

Keywords: Metal-carbon electrocatalysts, bimetallic nanoparticles, Catalysis, Platinum, X-ray absorption spectroscopy, atomic structure

As a rule, the information they have guides for fatigue testing geometrical designs, gives only the evaluation of the characteristics and design lay stock in several, and sometimes in tens times exceeds the tensile strength of the material. And saving of material, from the point of view of obsolescence, product should be developed on a certain resource. For details, which operate in the field of elastic deformations and calculated in operation for a given mode of operation should lay in the design of the guaranteed resource. To do this, for example, compensating coupling method is suggested, which is based on the calculation methods of CAD/CAM/CAE/CSE NX 7.5 and field tests considering the impact of technology of surface hardening. The character of strain in «elastic element» in NX 7.5. The calculations of the elastic element module «flexible body» NX 7.5, but due to the fact that the calculation is impossible to consider technological parameters of manufac-turing is conducted equivalent full-scale tests. Accordingly, designed and built a stand for equiva-lent tests. Finally, for comparison, is a computer simulation to calculate large displacements and complicated movements of the coupling. For this we used the application NX 7.5 «Simulation of kinematic mechanisms» with the attraction tools «Flexible body».

Keywords: diversification of management, production diversification, financial and economic purposes of a diversification, technological purposes of ensuring flexibility of production

To date, questions the reliability and continuity of electrical energy production facilities are among the most urgent , due to the transition generation companies into private hands and aggravate financial, economic and industrial- technological challenges : depreciation and obsolescence of equipment, lack of investment and other factors, influencing the power producers .
The article discusses the various valuation techniques of industrial enterprises and industrial complexes electricity . On the basis of their proposed universal method of estimating production complexes electricity , which is divided into 6 groups and includes weights . The article noted that the proposed method of estimating the weight of electric power systems operation has several advantages compared with the methods of other authors.

Keywords: electricity, electricity production complexes, investment, reliability, development

This article is devoted to description of structure of methodology of modelling of hierarchical problem-directed systems on the example of social and economic systems. In the basis of methodology the principle of a combination of the formalized methods of modelling and expert procedures is put. Modelling of hierarchical system is offered to be spent by means of multilayered fuzzy cognitive maps. Filling of the block of logical-mathematical models in structure of process of decision-making is described in detail. The offered methodology provides the development and choice of well-founded administrative decisions.

Keywords: Problem-directed system, decision making, fuzzy cognitive model, methodology

History rural fire insurance on the Don, analysis of insurance institutions Don Army (1870-1876), 
regional rural council (1876-1882), the Regional Management Committee for Zemstvo Affairs (1882-1919). 
The specificity of the insurance for the сossack population: collecting insurance payments stanichno and county boards, 
the choice of the сossacks rated insurance, etc. 
There was a preponderance of mutual insurance, analyzed the accumulation of insurance capital  

Keywords: insurance, organization of insurance, business, Zemstvo insurance, mutual insurance, insured event, insurance valuation, insurance discounts