The article deals with current methods of evaluating the organization and management in construction under conditions of uncertainty. The typology of the failure process is given, which determines the scenario of the crisis development at the enterprise. A model of forecasting and management in a crisis is proposed, and the conceptual aspects of building this model are considered. It is proposed to improve the enterprise management system based on the analysis of the economic component as a temporary function. Recommendations are given for improving the existing organizational forms of enterprise management.

Keywords: construction organization, organizational and technological solutions, reliability assessment, construction quality assessment

Questions of accounting of actors of influence on the investment and construction cycle are raised. An example of the use of BIM-technologies in construction is considered. It describes the solution of some specific problems that arise when maintaining the quality of construction of complex buildings, taking into account the possibility of introducing modern information systems, attention is paid to the peculiarities of improving the quality of work performed.

Keywords: organization of construction; quality of design, quality of construction and installation works, BIM-technology

The directions of modern research in the field of adaptive error correction, which can be applied when transmitting images in JPEG 2000 format over a noisy channel, are examined. Adaptive correction at the network level allows you to maintain a given percentage of packet delivery. Uneven protection at the application level is intended for use in broadcast broadcasts and allows the consumer to receive an image of various quality depending on the state of the network. Adaptive uniform protection at the application level is focused on point-to-point transmission and is aimed at receiving the maximum image quality by the receiver. The network layer tools discussed can be combined with the application layer tools.

Keywords: adaptation, noise-proof coding, forward error correction, noisy channel, JPEG 2000

the article deals with new methods of accounting and registration system of real estate, based on the introduction of blockchain technologies, which are primarily designed to optimize the procedure of registration of real estate and are decentralized networks that can significantly improve its efficiency.

Keywords: real estate, real estate management, regulation of land and property relations, registration of rights, accounting and registration procedures, legislative system, information database, cadastral registration of real estate, blockchain technology, transac

The mining industry, as well as the socio-economic development of this sector, makes a significant contribution to the development of the economy of some low-and middle-income countries rich in non-fuel minerals, as evidenced by the modified mining contribution Index (IVGP-BP). 10 of the 20 countries in which the mining industry contributes the most (the highest GPI-BP) rose one or two positions higher, according to the world Bank's country classification, between 1999 and 2019. Based on detailed data from the mining sector, such as mining, exports, prices, rents for mineral resources, mineral exploration expenditures, and state budget revenues, the current situation for 2019 is analyzed, as well as trends regarding the contribution to the development of the socio-economic level of the mining industry for 1999-2019.

Keywords: mining, minerals, industry, economy, export, mineral rent, gold, coal

Results of modeling and a pilot study of a low-pass filter with a cut-off frequency of 4 GHz are given. Modeling of the filter was carried out in MicrowaveOffice application program package. The experiment was made on the vector analyzer of RXA chains. Results of modeling and an experiment conform to the imposed requirements, namely: - cut-off frequency is 4 GHz; - losses in bandwidth no more than 3 dB; - an obstacle on the second harmonic of cut-off frequency not less than 60 dB; - wave resistance of an input and exit of 50 Ohms.

Keywords: low-pass filter; cut-off frequency; losses in bandwidth; losses in an obstacle band; modeling; experiment

Models of monitoring program generation systems are proposed that can significantly reduce the cost of time and other resources for monitoring complex technical objects. Systems are considered at several levels: subsystems and modules, communication links, usage scenarios, physical representations. A technique for adapting system models to subject areas is proposed.

Keywords: complex technical object, monitoring, models of software systems, program generation

When forming in the process of centrifugation an annular section by the method of ""separate"" concreting with the formation of a section of the product at the first stage from the original, including fine-grained concrete mixture, and with the introduction of a coarse aggregate at the second stage into the formed circular section, followed by the final formation of the section and compaction of the concrete mixture by centrifugation, the speed, calculated for the compaction stage, increases, depending on the section zone, the concrete compressive strength from 20% up to 47%, the initial modulus of elasticity from 6 to 19% relative to single-stage centrifugation. The ratio vint / vext of ultrasonic pulse velocities for surface sounding along the inner (vint) and outer (vext) faces of a centrifuged annular section can be considered as a conditional indicator of the uniformity of the concrete structure over the cross section of a centrifuged product. Key words: centrifugation, separate concreting, structure homogeneity, strength and deformation properties, porosity.

Keywords: centrifugation, separate concreting, uniformity of structure, strength and deformation properties, porosity

Within approaching the plane-stress state the problem of a high-speed rotating disk being under side pressure is considered. Within the model of a perfect rigid-plastic body and the Mises yield criterion the values of external parameters for which the plastic zones appear have been defined. The stresses in plastic zones are obtained from the solution of the Cauchy problem, which includes two differential equations to define the stress tensor nonzero component. In order to estimate the stress state in the elastic zone the equivalent stress is introduced. The maximum allowable values of external parameters are obtained from the solution of the problem when the disk is in the limit state. The numerical results are represented as the stress vector hodograph.

Keywords: the plane-stress state, Mises yield criterion, the equivalent stress, an elasto-plastic solid, a rotating disk, a stress vector hodograph

Of the existing methods of treating industrial wastewater (mechanical, chemical, physico-chemical and biological), it is the biological method that is of interest today, due to the fact that it is based on the ability of microorganisms and higher aquatic plants to use a variety of pollutants as a power source in the process of life, which ultimately leads to the purification of contaminated water. In the practice of wastewater treatment by the biological method, a floating plant — eichornia (water hyacinth) —was best established on the surface of the roots of which selective microbiocenoses are formed, which contribute to active biodegradation and absorption of both organic and mineral substances. The paper shows the possibility of echornia absorption of pollutants in an indoor environment and proved the possibility of purifying contaminated water with aqueous hyacinth in an indoor environment.

Keywords: water hyacinth, eichornia, pollutants, wastewater, higher aquatic plants

Finite state machines, being a mathematical abstraction, allow you to perceive information from the control object, process it and give signals to control the object. The disadvantages of the representation of complex production systems by a set of finite state machines include the complexity of carrying out logical and set-theoretic operations on them and the complexity of describing the parallelism that occurs in the operation of complex production systems. When specifying a finite state machine in the matrix–predicate form, due to the information redundancy, it is possible to avoid these difficulties. Matrix–predicate method allows you to uniquely set the finite state machine square matrix, which makes it possible to use the methods of the theory of matrices during the set–theoretic operations on them and it is possible to avoid isomorphism. The paper presents the developed methods of representation of a finite state machine using a multi-place predicate, which greatly simplifies its task.

Keywords: finite state machine, graph, matrix, predicate, algorithm, matrix–predicate method, graph incident, tuple, Cartesian product, complex production systems

Mathematic modeling of the state of a thin round disk being heat and force affected is performed. In the central part of the disk the homogeneous field of temperatures is formed. Within the deformation theory of a perfect elasto-plastic solid the quadratic plasticity condition is chosen. The relationships between the radius of the disk, the temperature of the central part of the disk and the external pressure which defines the appearance of plastic zones have been established. For different values of external parameters of the model the stress vector hodograph and the plots of stresses and equivalent stresses have been introduced.

Keywords: mathematic modeling, an elastic-plastic solid, the plane-stress state, the deformation theory, thermo-elasto-plasticity, a high-speed rotating disk

In this paper, research on the development of methods for the production of thermoplastic elastomers for construction purposes based on styrene-butadiene-styrene rubber filled with expanded perlite, studied the performance characteristics of these materials. Various methods for the modification of thermoplastic elastomers, their processing modes and methods of controlling their properties are considered.

Keywords: thermoplastic elastomers, expanded perlite, production methods, material characteristics, density, physical and mechanical properties

Despite numerous advantages, green construction has not yet acquired significant proportions, since modern environmental technologies in construction lead to increased costs, and legislation is also not being adapted to new certification systems. This article outlined the main objectives of "green" construction. Considered the most important principles on which it is based. Analyzed the modern "green" standards for environmental performance of buildings, discussed in detail the methods for determining the rating of a building on specific scales. The advantages and disadvantages of environmental standards were also noted, groups of organizations in the field of “green” construction in Russia were considered.

Keywords: environmental technology, green building, green standards, energy saving, energy efficiency, energy consumption, green building, renewable energy sources

At present, modern information technologies are actively used in the design of complex equipment at various industrial enterprises – automated systems for end-to-end CAD/CAM/CAE class design, which provide complex execution of design work with a significant reduction in their execution time while improving the quality of work. When this is achieved the main objective which is the update of the nomenclature of products, reducing costs, improving reliability, efficiency, etc. In view of this, the task of constructing and visualizing solid-state models is relevant today. From the analysis of the literature, it was concluded that today there are not enough methodological techniques for building models, and the existing developments do not contain optimal algorithms for creating 3D models of parts of varying complexity. Therefore, to implement the above problem, an algorithm for constructing a 3D model with a cutout was proposed.

Keywords: CAD/CAM/CAE, graphic packages, projection drawing, computer graphics, construction algorithm, geometric body, solid modeling, software, 3D model, surface toning